Choosing a home projector comes down to four numbers on the spec sheet that manufacturers inflate most often: brightness measured under a recognised standard (ANSI lumens or ISO 21118, never bare ‘LED lumens’), native resolution rather than accepted signal, throw ratio to know where the unit fits, and noise in decibels in the mode you will actually use. A projector makes sense when you want an image beyond 100 inches and can darken the room; otherwise a large television remains the safer bet.
- Brightness: Look for ANSI or ISO 21118 figures. A 100–120 inch screen in a dark room needs roughly 2,000 lumens; with ambient light, 3,000 or more.
- Resolution: Check the ‘native resolution’ or ‘panel’ line. ‘4K compatible’ or ‘supports 4K’ usually means a 1080p panel accepting a 4K signal.
- Placement: Throw ratio equals distance divided by image width. Short-throw models deliver 100 inches from under 3 metres.
- Noise: Compare decibels and brightness from the same mode, not the headline brightness against the eco-mode noise.
Why not all lumens are equal
ANSI lumens are obtained by measuring brightness at nine points on the screen and averaging them. ISO 21118 is the international standard Epson uses for white brightness, and it is closely comparable to ANSI. What is not comparable is ‘LED lumens’ or ‘light-source lumens’, which can multiply the real figure by 10, 20 or even 30. A mini projector advertising ‘12,000 lumens’ often delivers between 100 and 300 ANSI lumens.
The warning is not theoretical. In February 2024, Dangbei agreed to settle a lawsuit filed by Epson by correcting the worldwide brightness specification of its Mars Pro model from 3,200 to 1,800 lumens and adopting standards such as ISO 21118. That is Epson’s account, and Epson is a competitor, but the correction represents a 44% reduction on paper.
Brightness also depends on the operating mode. Epson’s Home Cinema 2350 is rated at 2,800 ISO lumens in its brightest mode, 2,300 in standard and 1,900 in eco. The big number on the box is the one from the loudest mode.
Native 4K, pixel shifting and ‘4K compatible’
These are three different things, and spec sheets tend to label all of them ‘4K’. A native 4K panel has 3,840 × 2,160 physical pixels, around 8.3 million. Everything else reaches the screen through tricks or not at all.
The most widespread trick is pixel shifting. Texas Instruments explains in the datasheet for its DLP 4K UHD chip that the switching speed of its micromirrors allows 8.3 million pixels to be displayed, a resolution equivalent to combining four 1080p images. Epson does something similar in LCD: its 4K Enhancement technology shifts each pixel diagonally to double Full HD resolution, as described on the Pro Cinema 4050 page, whose panels are 1,920 × 1,080. The result can look sharper than plain 1080p, but it is not the same as a native panel.
The third category is ‘4K compatible’ or ‘accepts 4K’: the projector takes the signal but displays it at its native resolution. The Epson HC2350, for instance, has a resolution of 1,920 × 1,080 pixels (‘3,840 × 2,160 with 4K Enhancement’) and its format table lists inputs up to 4,096 × 2,160. A practical rule: find the ‘native resolution’ or ‘panel’ line. If only ‘4K’ appears next to ‘support’, ‘compatible’ or ‘decoding’, assume the panel is lower resolution.
Throw ratio, short throw and real-world noise
Throw ratio is the distance to the wall divided by the image width. With a ratio of 2.0, every metre of image width requires two metres of distance. A 100-inch 16:9 screen is about 2.2 metres wide, so a 2.0-ratio projector sits roughly 4.4 metres away, usually ceiling-mounted behind the sofa.
BenQ classifies as short throw any projector delivering 100 inches from less than 3 metres. Its TK700STi example has a ratio of 0.9 to 1.0 and produces those 100 inches at about 2 metres. Measure first and choose afterwards; many projectors have zoom, but BenQ advises against relying on it when the unit is permanently installed, as it can affect image quality.
Noise is louder than expected in quiet scenes and rises with brightness. The Epson HC2350 is rated at 36 dB in its brightest mode, 32 dB in standard and 28 dB in eco. The Pro Cinema 4050 is listed at 20 to 31 dB of fan noise. The trap: the HC2350’s 28 dB comes with 1,900 lumens, not the headline 2,800. Lamp life also depends on mode: the 4050’s lamp lasts up to 5,000 hours in eco and 3,500 in high.
Contrast deserves equal scrutiny. BenQ warns that FOFO contrast, which compares full white with full black, is misleading; ANSI contrast, measured across a checkerboard of 16 white and black rectangles, gives more useful numbers but is rarely published. With light in the room, contrast suffers more on a projector than on a television, because the image forms on a wall or screen that also reflects ambient light.
The verdict is situational. A well-chosen projector delivers an experience no television matches for the same money, but only in the right room. If you watch sport at noon with sunlight flooding the living room, buy the TV. If you watch films at night and can lower the blinds, the projector wins, provided the spec sheet states which standard measures the light and how many pixels the panel really has. A sheet that omits both is already telling you something.
Sources & References